Differences

This shows you the differences between two versions of the page.

--- home_automation [2025/08/17 15:50] – w5ged
+++ home_automation [2025/12/14 18:24] (current) – w5ged
@@ Line 1: / Line 1: @@
 ====== Home Automation System ======
-I'm using [[https://www.home-assistant.io/|Home Assistant]] running on a [[https://www.raspberrypi.com/|Raspberry Pi]] 3.
+I'm using [[https://www.home-assistant.io/|Home Assistant]] running on a [[https://www.raspberrypi.com/|Raspberry Pi]] 4.
-Whenever possible, I use WiFi to communicate between remote devices.
+Whenever possible, I use WiFi to communicate with remote devices.
 Integrations include:
@@ Line 27: / Line 27: @@
   * [[https://templates.blakadder.com/sonoff_S31.html|Sonoff S31]] - Used to monitor power consumption & control outlets
   * [[https://templates.blakadder.com/slampher.html|Sonoff Slampher R2]] - Table lamp
-  * [[https://templates.blakadder.com/sonoff_THR320D.html|Sonoff THR320D]] - Used to monitor temperature/humidity and control an attic exhaust fan
+  * [[https://templates.blakadder.com/sonoff_THR320D.html|Sonoff THR320D]] - Monitors attic temperature/humidity and controls an exhaust fan (Sensor SI7021 requires "DhtDelay 500,40")
   * [[https://templates.blakadder.com/sonoff_TX-T0US3C.html|Sonoff TX T0US3C]] - Wall switch used to control 3 devices
   * [[https://templates.blakadder.com/sonoff_NSPanel.html|Sonoff NSPanel Touch Display Switch]] - Wall switch and display
@@ Line 34: / Line 34: @@
 Sensors
   * [[https://www.analog.com/media/en/technical-documentation/data-sheets/ds18b20.pdf|Analog Devices DS18B20]]
-  * [[https://components101.com/sensors/dht22-pinout-specs-datasheet|DHT22]] - Do not use with a Raspberry Pi
+  * [[https://components101.com/sensors/dht22-pinout-specs-datasheet|DHT22]] - Do not use the Raspberry Pi Adafruit library
   * [[https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bme280-ds002.pdf|Bosch BME280]]
   * [[https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp280-ds001.pdf|Bosch BMP280]]
@@ Line 43: / Line 43: @@
   * [[https://www.lilygo.cc/products/t-beamsupreme-m?variant=43067944173749|LilyGo ESP32-S3 LoRa Development Board with SX1262 868/915MHz GPS U-blox L76K]] - aka: T-BeamSUPREME (M)
   * [[https://store.rakwireless.com/products/wisblock-meshtastic-starter-kit?variant=41433735758022|RAK WisBlock]] - aka: with u-blox ZOE-M8Q, OLED Display & solar enclosure
+Tasmota Rules:
+  * Control a remote switch based upon a local temperature value
+  Rule1
+  ON Tele-DS18B20-1#Temperature>80 do WebSend [IPADDRESS] Power1 1 BREAK
+  ON Tele-DS18B20-1#Temperature<75 do WebSend [IPADDRESS] Power1 0 ENDON