Differences

This shows you the differences between two versions of the page.

--- home_automation [2025/09/30 23:53] – w5ged
+++ home_automation [2026/08/13 15:17] (current) – w5ged
@@ Line 1: / Line 1: @@
 ====== Home Automation System ======
-I'm using [[https://www.home-assistant.io/|Home Assistant]] running on a [[https://www.raspberrypi.com/|Raspberry Pi]] 4.
+I'm using [[https://www.home-assistant.io/|Home Assistant]] running in a Proxmox Virtual Machine.
 Whenever possible, I use WiFi to communicate with remote devices.
@@ Line 27: / Line 27: @@
   * [[https://templates.blakadder.com/sonoff_S31.html|Sonoff S31]] - Used to monitor power consumption & control outlets
   * [[https://templates.blakadder.com/slampher.html|Sonoff Slampher R2]] - Table lamp
-  * [[https://templates.blakadder.com/sonoff_THR320D.html|Sonoff THR320D]] - Used to monitor temperature/humidity and control an attic exhaust fan
+  * [[https://templates.blakadder.com/sonoff_THR320D.html|Sonoff THR320D]] - Monitors attic temperature/humidity and controls an exhaust fan (Sensor SI7021 requires "DhtDelay 500,40")
   * [[https://templates.blakadder.com/sonoff_TX-T0US3C.html|Sonoff TX T0US3C]] - Wall switch used to control 3 devices
   * [[https://templates.blakadder.com/sonoff_NSPanel.html|Sonoff NSPanel Touch Display Switch]] - Wall switch and display
@@ Line 44: / Line 44: @@
   * [[https://store.rakwireless.com/products/wisblock-meshtastic-starter-kit?variant=41433735758022|RAK WisBlock]] - aka: with u-blox ZOE-M8Q, OLED Display & solar enclosure
-Tasmota Rules:
+====Sample Tasmota device====
-  * Control a remote switch based upon a local temperature value
-  Rule1
+  GPIO1    Switch1   Fire alarm contact closure input
-  ON Tele-DS18B20-1#Temperature>80 do WebSend [IPADDRESS] Power1 1 BREAK
+  GPIO2    Relay1    Contact closure output
-  ON Tele-DS18B20-1#Temperature<75 do WebSend [IPADDRESS] Power1 0 ENDON
+  GPIO7    AM2301    HVAC Supply Temperature/Humidity
+  GPIO43   Buzzer    Buzzer
+  GPIO44   AM2301    Free Air Temperature/Humidity
+The XIAO-ESP32S3 devices use firmware: tasmota32s3.bin with the template configuration:
+  {"NAME":"GED-ESP32S3","ARCH":"ESP32S3","GPIO":[32,1,1,1,1,1,1,1,1,1,0,0,0,0,0,0,0,0,0,0,0,544,0,0,0,0,0,0,0,0,0,0,1,1,0,0,0,0],"FLAG":0,"BASE":1}
+Devices can be configured by browsing to their IP address & going to Tools/Console.
+  Tasmota settings:
+  Setoption8 On (Output temperature in °F)
+  Teleperiod 60 (Report to MQTT server every 60 seconds)
+  SwitchMode1 2 (when the GPIO pin is pulled low during a contact closure it reports "ON")
+  Rule1    Relay state follows the contact closure state
+  ON Switch1#State DO Power1 %value% ENDON
+  Rule2    Sound the buzzer then a contact closure is detected
+  ON Switch1#State=1 DO Buzzer 1,5,1 ENDON
+  Rule3    Control a spot cooler based upon two temperature sensors
+  ON Switch1#State=1 DO WebSend [192.168.10.170] Power1 0 BREAK
+  ON Tele-AM2301-07#Temperature>80 do WebSend [192.168.10.170] Power1 1 BREAK
+  ON Tele-AM2301-44#Temperature<80 do WebSend [192.168.10.170] Power1 0 ENDON